Call

 

Are you looking for information on How to Install a Bathtub?

Setting up a tub isn't specifically brain surgery, but it does require solid plumbing, carpentry, and in some cases, tiling abilities. Changing an old tub with a new one is likewise a moderately difficult task. If the old bathtub is easily accessible, the job can move quickly; if you have to open a wall surface to eliminate the old tub and place the brand-new tub, the task is a lot harder. In either situation, the project is within a residence handyman's skills, although you will certainly need an assistant to leave the old tub and also set in the brand-new one. Ensure you have actually qualified on your own for the job as well as fit attempting it. As opposed to hiring a service provider to take over a halfway-completed job, it is far better to consider utilizing one before you begin. Opportunities are you might require a specialist plumber to make tube links.
This short article will assist you install a new bathtub in your washroom if you have actually currently purchased a new tub as well as don't require to transform the setup of your previous water supply pipes.
Your devices as well as product checklist should consist of the following:

 

• New Bath tub


• Hammer


• Pipeline Wrenches


• Prybar


• Safety Glasses


• Level


• Pliers


• Adjustable Wrench


• Putty Knife


• Screwdriver


• Cold Chisel


• Measuring tape


• Pipe Caps


 

Removing Old Touches

If you need to replace old faucets with new ones as a part of your installment, then the first thing you need to do is disconnect the water supply. After doing so, switch on the faucets to drain any type of water remaining in the system. The process of getting rid of the existing faucets can be quite bothersome due to the restricted accessibility that is typically the situation.
Make use of a container wrench (crowsfoot spanner) or a faucet device to reverse the nut that attaches the supply pipes to the faucets. Have a cloth ready for the staying water that will come from the pipes. When the supply pipelines have been eliminated, utilize the same tool to loosen up the nut that holds the faucets onto the bath/basin. You will need to quit the single taps from transforming during this process. When the taps have actually been eliminated, the holes in the bath/basin will need to be cleaned up of any type of old sealing substance.
Before going on to fit the brand-new faucets, compare the pipeline connections on the old faucets to the new faucets. If the old faucets are longer than the new faucets, then a shank adapter is needed for the brand-new taps to fit.

 

 

Fitting New Touches

If the tails of the new taps are plastic, after that you will certainly need a plastic adapter to prevent damages to the string. One end of the adapter fits on the plastic tail of the tap as well as the other end offers a link to the existent supply pipes.
If you need to fit a monobloc, then you will need lowering couplers, which attaches the 10mm pipeline of the monobloc to the standard 15mm supply pipeline.
Next off, place the tap in the mounting hole in the bath/basin guaranteeing that the washers remain in location between the tap and also the sink. Safeguard the tap in place with the supplier given backnut. When the tap is securely in position, the supply pipes can be connected to the tails of the faucets. The faucets can either be linked by using corrugated copper piping or with regular tap ports. The former type needs to be linked to the faucet ends initially, tightening just by hand. The supply pipelines can later on be connected to the various other end. Tighten up both ends with a spanner after both ends have actually been attached.

 

 

Setting up the Bath tub

Making use of both wood boards under its feet, position the bathtub in the required placement. The wood boards are helpful in equally spreading out the weight of the bathtub over the location of the boards rather than concentrating all the weight onto 4 tiny points.
The following goal is to make certain that the bath tub is leveled all round. This can be achieved by inspecting the level as well as changing the feet on the tub till the spirit level checks out level.
To install faucets, fit all-time low of the outermost versatile faucet adapter to the ideal supply pipe by making a compression sign up with; after that do the exact same for the various other tap.
Activate the water and inspect all joints and also brand-new pipework for leaks as well as tighten them if required. Fill the bathtub as well as likewise check the overflow electrical outlet and the regular electrical outlet for leakages.
Ultimately, deal with the bathroom paneling as defined in the producer's user's manual. Tiling and sealing around the bathtub must wait until the tub has actually been utilized at the very least once as this will resolve it into its final setting.

 

 

Preparing for the Setup

To start with, the supporting frame provided with the bathroom needs to be fitted (if called for) according to the maker's guidelines. Next, fit the faucets or mixer to the bath tub. When suitable the faucet block, it is important to make sure that if the tap includes a plastic washing machine, it is fitted between the bath as well as the taps. On a plastic bathroom, it is additionally sensible to fit a sustaining plate under the faucets unit to avoid pressure on the bath tub.
Fit the adaptable tap adapters to the bottom of both faucets using 2 nuts and olives (sometimes provided with the bathtub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink electrical outlet opening, and afterwards pass the electrical outlet through the hole in the bath. Make use of the nut provided by the supplier to fit the plug-hole. Check out the plug-hole outlet for an inlet on the side for the overflow pipeline.
Next off, fit completion of the adaptable overflow pipeline to the overflow outlet. Afterwards, screw the pipe to the overflow face which ought to be fitted inside the bath. Ensure you make use of all of the provided washers.
Attach the trap to the bottom of the waste electrical outlet on the bathtub by winding the thread of the waste electrical outlet with silicone mastic or PTFE tape, and also screw on the trap to the outlet. Connect all-time low of the overflow tube in a comparable manner.The bath ought to currently prepare to be suited its final setting.

 

 

Tiling Around the Bathtub

In the location where the bath meets the tile, it is necessary to seal the joins with a silicone rubber caulking. This is necessary as the fitting can relocate sufficient to break an inflexible seal, causing the water to penetrate the wall surface in between the bathroom and the tiling, bring about difficulties with moisture and feasible leakages to the ceiling below.
You can select from a selection of coloured sealants to assimilate your components and fittings. They are offered in tubes as well as cartridges, and can securing spaces up to a width of 3mm (1/8 inch). If you have a larger void to fill up, you can load it with twists of drenched paper or soft rope. Remember to always load the bath tub with water before sealing, to allow for the movement experienced when the bathtub remains in use. The sealer can fracture rather very early if you do not think about this motion before securing.
Conversely, ceramic coving or quadrant floor tiles can be made use of to border the bathroom or shower tray. Plastic strips of coving, which are easy to use and cut to size, are also conveniently offered on the market. It is a good idea to fit the tiles making use of waterproof or water resistant adhesive and also cement.

 

A Step-by-Step Guide to Installing a Bathtub

 

Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.

But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.

This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.

 

Remove the Existing Bathtub

 

To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.

The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.

 

Choose the Right Bathtub

 

The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.

 

Install the Plumbing and Ledger Board

 

You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.

Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.

 

Install the Bathtub

 

When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.

Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.

If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.

 

Hook up the Plumbing

 

Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.

 

Install the Bathtub Surround

 

A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.

Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.

If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.

If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.

https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/

 

Do you like more info about Installing A Bathtub? Place feedback down below. We will be interested to listen to your thoughts about this blog post. We are looking forward that you visit us again in the future. Enjoyed reading our posting? Please share it. Let someone else discover it. Thanks for your time. Kindly check our blog back soon.

24/7 emergency? We're here!